dannrathers Posted February 7, 2012 Share Posted February 7, 2012 OK.. small problem here. I did this job and replaced all the gaskets and the thread in pvc valve. Well..put it back together and went to start it up.. It starts and then dies UNLESS i give it a bit of gas as it starts up. Then it runs normal. ANyone know the torq on the intake bolts? I did them by hand and made sure they were tight. I did not use any gasket maker..anyone think this would help? I did take everything apart again..then back together again and the same thing happens. ANY IDEAS? It's been about 1 month since last time I did it and I just have to tap the gas as it start up every time. This gets it running normal. Its been cold here and I haven't had the time to try it again with some gasket maker. I can only think its a vacuum leak..but it's weird that it runs ok after i tap the gas at start up. Link to comment Share on other sites More sharing options...
Towncivilian Posted February 8, 2012 Share Posted February 8, 2012 See page EM-10 for torque specs for all of the removed hardware, and EM-12 for the upper intake manifold bolts. RTV/gasket maker is unnecessary for replacement of the gaskets for the throttle body, upper intake manifold gaskets, and lower intake manifold gaskets. Link to comment Share on other sites More sharing options...
deltaR50 Posted August 4, 2013 Share Posted August 4, 2013 (edited) i recently did both power valves and swirls valves while at it,replaced the old screws with new ones. got them 24 cents per screw from ace hardware. size and thread pattern is m3x.50 10mm length, then used the high strength red loctite so i would have a peace of mind those screws wont come out. i would recommend to change the intake manifold gasket, pcv,valve cover, spark plug seal, emission valve cover hose that connects both valve cover since they are plastic and get brittle, while u work down there because everything has easy access while the intake manifold is out. do it once and do it right the first time. as the torque for the intake manifold. i did all 12mm bolts and nuts at 20lbs. Edited August 4, 2013 by deltaR50 Link to comment Share on other sites More sharing options...
NovaPath Posted January 31, 2015 Share Posted January 31, 2015 Just finished this up about 10 minutes ago. I really appreciated your how to, although I deviated slightly and did not remove the throttle body. For anyone about to do this, have some extra vacuum line on hand as a couple of mine broke upon trying to remove. I'm sure the act it is 24 degrees out didn't help, though. For what it's worth all of mine were tight and most likely would never have come out on their own, but a decent amount of red lock tite on each screw will now make sure of that. Got it all done in about 3 hours, including spark plug change while I was at it. This was doing the work behind my townhouse on the side of the street in freezing temps too, so I don't want to hear anyone's excuses! 1 Link to comment Share on other sites More sharing options...
BowTied Posted February 27, 2016 Author Share Posted February 27, 2016 Well, I have final update. I sold the pathfinder not long ago with 217k km on the clock. She was still running strong and never any issues with the power valves. I hope runs many years for the new owners. Thanks to everyone who showed thier appreciation for my post and also to those who added or expanded on the info with newer and better ways to do things. Cheers. Link to comment Share on other sites More sharing options...
98dreamer Posted November 24, 2020 Share Posted November 24, 2020 Sorry. Very new. My 1st question is what exactly are you all calling power valves and swirl valves? And can you provide pictures of each? Link to comment Share on other sites More sharing options...
Slartibartfast Posted November 26, 2020 Share Posted November 26, 2020 This thread's probably got the best pictures you're gonna find. There should be a diagram in the service manual (get it here for free) that makes their location and function clearer. If you have a '98, though, good news! Your VG33E doesn't have power valves or swirl valves. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now