Dave.Bert

I am wanting to put a basket on the rack to mount lights antenna etc. is the rack that is there ok to mount a basket to? thank you

I am wanting to remove the Roof Rack with the spoiler looking thing in front and install the one with the bard across the top(like the silver pathy) Is it possible to do this? thank you

Hello I am wanting to mount a LED light in the front bumper as a fog light and need input. I am looking at either a 12" or 20 inch light for this. Has anyone mounted a light there and have any suggestions on what size to mount there? also i am wanting to tie the wiring for the light into the wiring for the OEM fog lights. Is this ok or will that freak the computer our? Or pull too much power for the system? Also has anyone installed a LED light bar on the roof of your pathy? Id like to see how the light bar was mounted as well as how it was wired in. and last of all WHERE did you get your light ? Thanks Ya all for the help

Hello I am looking to replace the bushings on my pathie with new Polyurethane bushings There is a choice between a solid bushing and a split bushing. Other than ease of installation, is there an advantage/disadvantage in one vs the other? Does the Solid bushing last longer then the split bushing? Any input on this would be greatly appreciated

I am currently in the process of purchasing the parts i need to replace the front suspension on my pathfinder I already have the KYB Excel-g struts and the KYB SM5329 mounting kit and the OME springs. what other seats etc from the diagram below should i replace as i install the new parts

ok tonight i have ordered the OME suspension without the front struts. I am getting the KYBs for the front. I was looking at the stock fog lights and am wondering if there is a good upgrade for them?

I purchased a 2004 Pathfinder LE I have been doing a lot of reading here and on other forums. I am wanting to redo the suspension. The Odometer has over 200K miles so i am thinking that the suspension is pretty much toast. I am to replace the warn suspension that is there with something better. The parts that i have questions are the shock/struts and springs. I am looking at using the Old man emu springs and shocks and the KYB Excel-Gs struts in front. Has anyone tried this setup? Can anyone give me any suggestions? Also will the 1.5 to 2 in lift that comes with the OME setup cause issues with the CV joints int he shafts? I am going to be installing Manual locking hubs in the front(Rugged Ridge 15001.61) With .25 inch spacersTrans-Dapt Performance Disc Brake Spacers 7107 (http://www.summitracing.com/parts/TRD-7107/) . I know that i need to redo the studs. can i use the same ones that are for the rear or do i need to use a M12x1.5(necessitating new lug nuts)? With the spacers installed what is the largest tire that i can install? what would be a good tire to install for both on and offroad as well as snow on the roads? I am going to do a Missing link. I can fab one myself It is going to cost me about $10 ill post pics of what i build. Future Mods are: Skid Plates at least front and possibly middle Front brush guard Tail light guards Lights in front and rear and on top. How have you run the wiring for the lights? and mounting suggestions. I am planning on installing a ham radio and a CB radio. Does anyone have any pics of the install of the radio as well as the install of the antennas? Any suggestions on the wiring for the power of the radios? This is a partial list of threads that i have read so far on my '04 R50 http://www.nissanpathfinders.net/forum/topic/39147-longer-wheel-stud-options/ http://www.nissanpathfinders.net/forum/topic/33354-manual-locking-hubs-with-stock-03-04-wheels/ Any other suggestions for recommended reading on this forum or others

I recently purchased my 2004 Pathfinder and have installed a transmission cooler (first mod). I have to top off the fluid. Do i go ahead and use the matic D that manual calls for or Merc III that can be used in its place. I just purchased this vehicle so i dont know that is in it now thanks

Hello I know there is an issue with the in the radiator transmission cooler and would like to install an external one. Should i get an aftermarket one or is there a OEM one from another vehicle that would fit? Is there already a thread about Trans coolers? thank Ya All