doughboy Posted April 5, 2007 Share Posted April 5, 2007 I'm going to pick up my 5 speed Tuesday, and I need to know everything I will need to pull off the dead pathy. I know some of you have done it and would know, so any wisdom would be greatly appreciated Link to comment Share on other sites More sharing options...
Mookie Posted April 5, 2007 Share Posted April 5, 2007 Hey there, Have you done some searching yet? There are a few posts that cover what you are looking for. Link to comment Share on other sites More sharing options...
sammyb33 Posted April 5, 2007 Share Posted April 5, 2007 so mookie hows the leaf sprung pathfinder doing? and recent outings with pictures we could see??? Link to comment Share on other sites More sharing options...
sammyb33 Posted April 6, 2007 Share Posted April 6, 2007 but to answer your question... Transmission Pedals (both brake and clutch) Master Cylinder All Fluid Lines Slave Cylinder (if you can get it get the tranny cross member out of the manual pathfinder its not needed, but i had to re drill holes to fit my auto cross member back on) that is a basic list. PM milehighcowboy i believe somehow he got a complete listing from nissan every part that is needed, and he is currently doing his swap as well maybe he can point you in the right direction. Link to comment Share on other sites More sharing options...
milehighcowboy Posted April 6, 2007 Share Posted April 6, 2007 hey doughboy here is that list that sam is talking about. its a list me and a guy at the nissan dealership put together. its got a bunch of parts numbers that are no longer in use we were using a parts book form 1987 lol. but here ya go. Clutch Pedal Bracket 46550-0W501- 1 Brake Pedal and Bracket 46501-0W000- 1 Clutch Master cylinder 30610-0W050- 1 Clutch to dampener line 30850-0W000- 1 Clutch Dampener bolts 08146-6162G- 2 Clutch Dampener 30660-0W000- 1 Clutch Dampener to passenger fender line 30851-1W200- 1 Brake/Clutch transfer block ???? 1 Transfer block to Slave Cylinder hose line 30851-1W211- 1 Slave Cylinder hose bracket 50915-0W010- 1 Slave Cylinder hose bracket bolt 08156-8161F- 1 Slave Cylinder hose clip 46206-2J000- 1 Slave Cylinder rubber hose 30855-0W010- 1 Slave Cylinder banjo bolt copper seals 46237-A4600- 2 Slave cylinder banjo bolt 46356-0E000- 1 Slave cylinder 30620-0W020- 1 Slave cylinder bolts 08121-0251E- 2 Driveline Parts Clutch kit (clutch, pressure plate, throw out bearing) NU31214-1 (AutoZone part) 1 Throw out bearing support 30501-1C100- 1 throw out bearing control arm 30531-01S00- 1 throw out bearing control arm boot 30542-75P00- 1 transmission 32010-0W020- 1 transmission isolator (mount) bolts (bottom) 11258-D0101- 2 transmission isolator (mount) 11320-1W200- 1 Transmission bolts (top) 11393-0W000- 8 bell housing bolts M10 1.50 60-80mm 01121-06291- 8 Flywheel 12310-0W000- 1 Flywheel bolts M10 1.00 30mm 12315-D0210- 6 Pilot bearing 32202-B9500- 1 Transmission shifter 32839-62G00- 1 Transmission shifter knob 32865-50Y00- 1 Interior pieces Inspection hole cover 74810-0W000- 1 Body to transfer case and transmission mount with boots 74967-0W020- 1 Outer rubber boot with mount 74910-0W010- 1 Finisher console with boot 96934-0W010- 1 Electronic pieces ECM for Manual transmission 23710-1W600- 1 if you got any questions just shoot. ben Link to comment Share on other sites More sharing options...
packie88 Posted April 6, 2007 Share Posted April 6, 2007 if i recall you dont need a new ECM when going from a AT-MT but you do when going from a MT-AT Link to comment Share on other sites More sharing options...
sammyb33 Posted April 6, 2007 Share Posted April 6, 2007 correct. i still dont understand why the Nissan parts list has it on there.... Link to comment Share on other sites More sharing options...
milehighcowboy Posted April 6, 2007 Share Posted April 6, 2007 yea you dont need that thing he was insistent that i include it on the list. ben Link to comment Share on other sites More sharing options...
doughboy Posted April 11, 2007 Author Share Posted April 11, 2007 got my five speed today... minus the clutch/brake pedal assembly the kid bought the truck to destroy and did just that... next step.... put it in... here comes the fun Link to comment Share on other sites More sharing options...
vengeful Posted April 11, 2007 Share Posted April 11, 2007 Here's a detailed writeup that Keith did when he performed his 5-speed swap on his R50. It's tailored to the R50, but it applies to the WD21 as well, just have to modify a few things... http://www.overlandtrucks.com/system-f/NPTC.pdf Link to comment Share on other sites More sharing options...
milehighcowboy Posted April 11, 2007 Share Posted April 11, 2007 WTF??? that list and my list is the exact same. well now i know why the part number dont match up. classic stealership. well i guess my list was not original after all. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now