DantheMayun

OK. How are we going about this haha. You stopping by? Me shipping?

Are you swinging by tommorow? Give me a call text 717 881 6942

Not sure. I did paint it. It was this weird fadded out black before so I madde it look nice. The rear is alright I think it has a love tap in the corner but its not rusted out.

I also want to add that the whole top end of the engine has been rebuilt. Probably less than 300 miles on it. Have paperwork to prove it. Valves machined new timing chain. New gaskets. Maybe a couple of other things I forget.

I have it.

Mine are bad. So much wind noise come through them.

Radiator is fairly new. Replaced it maybe 3 years ago? Not so many miles put on it since then becuase my pos breaks down every winter. Hence why i'm getting rid of it lol.

I'd say its in good condition.

The dash is probably the nicest part on the rust bucket.

No sunroof.

I'm not too sure of what i'm looking at. Is that the bottem of the consol where the radio is? if so yes. I would imagine shipping would be hell.

No power anything on mine. Its the xe.

Im Sorry for the delay guys. I've been very busy between working 2 jobs and the rust bucket has been sitting on the back burner. Yes It's still sitting in the driveway. Again very sorry. My address is 50 Fairview Drive Hanover pa 17331 if anybody wants to come by and look at what I got. Let me sort through what you guys need and i'll try my best to help you out.

Also I want to add the engines top end has been completely rebuilt up to the pistons. New gaskets new timing belt. Valves machined ect ect. I kind of want to keep it because I want to drop it into the hardbody but If I don't I will sell it cheap.

Long story short everything interior is in very good condition. Dash is good, I do have a new radiator in it that I replaced a couple of years ago. Pretty much everything is nice on it but the frame. Its a 94 nissan pathfinder xe with gray interior. I will hold on to it if you guys want parts I wont scrap it right away. I will be keeping the wheels and tires though. Now how I'm going to get what you guys want is kind of uncharted waters for me. If you're close by and want to check it out what you want that's cool we could work that out. Ill gladly ship anything if you pay shipping. Now, I recently found a hardbody around me with a bad sending unit that's in pretty good shape rust wise haha. So the pathfinder will be sitting around as i'm figuring out what I want to do with it.

Hey after fighting my pathy for 5 years now with rust a breaking parts i've decided that if I go any further into fixing this thing it just a waste of my money. HOWEVER It does have some decent parts left and I figured i'd let you guys know. Tell me what you need and i'll see If i can get it to you. I live in Hanover PA so if you're local I might even drive it to your door!

I read up on how to readjust them. If i'm not mistaken you dont even have to take them out you have to just move the "anchor''? Th peice that you ajust with over just by tapping it out? Pretty cool. But i'm not sure if that's my problem here I dont see why my torsion bar is so loose.

http://www.youtube.com/watch?v=6VXb6sY2SGY#t=34 It doenst make sense to me this is a previos video at 30 sec you can see when i jiggle it the little mount that goes with it moves as well. Is that mount broken off?

well got around to doing it today.. Looks like my left t bar is broken. And theyre pretty much maxed out anyways. the bolt that you adjust is just dangling loose

Ive never cranked them and I really doubt the p/o did. Front end has always been a little low. To be honest though idk how to really tell if they have already been cranked

I want to install new rancho shocks and crank my t bars.. i'm worried cranking them might give me alignment issues. Where they're sitting now the guys at Firestone were unable to properly align my pathy. I have no idea what goes into alignment and I know unless you get it done at nissan everybody has a hard time. Hmm I wounder if I get new shocks in the front if I need to get new shocks for the back...

Yea and they seem to set in nice. I got the whole assembley new should be alright I think.

Dang 700$ what a steal. I dont think i could handle the broken manifold studs though.

Wow cvdloc makes mine look brand new.

http://www.youtube.com/watch?v=EFEppN1yFGU&feature=youtu.be Alrighty, finally got some time to upload it today. Happy Turkey Day guys! Gobble Gobble lets drink