Chymos
-
Posts
26 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Posts posted by Chymos
-
-
From what I've seen in the news, it was a '93, and the video clips I've seen of the wrecker hauling it off, it has the stock XE chrome steelies
-
Left side while sitting in the vehicle.
-
The 4wd D21 hardbody and all WD21s (both 2wd and 4wd) use an identical frame and drivetrain with the exception of the rear suspension. The pickups use leaf springs in the rear while (as we all know) Pathys use a multi-link setup.
-
I'm pretty much in the same boat here - lost a front stud getting the wheel off. I plan to replace all mine once I have the chance... though I don't have a press... or snap-ring pliars... or anything really... lol...
You shouldn't need a press. Just a small section of a 2x4 board and a hammer. As for snap-ring pliers, they're not too expensive (even if you get Craftsman ones).
If it's 2wd, you'll need a special socket (a 'wheel bearing locknut socket'. I'm not sure if you need it for 4wd Pathys). The cheapest place to find it is on ebay. I paid about $20 for mine. Parts stores around here don't carry the right one. They have 4-prong ones, but what you'd need is a 2-prong one. One that fits Honda will work fine.
Here's a link to the socket:
edit: Keep in mind that if you ford anything deep enough for the water to reach the hubs, you need to repack your wheel bearings ASAP afterwards just in case water gets into the hub/spindle assembly.
-
I've got one on mine. Check Ebay, they got plenty for around $60 to $100. Don't know if I'd recommend one though. Mine has lost hp I think. Had a lil more pick up with the stock intake. Go with a snorkel, that would be cool and you won't have to worry about water getting into the intake.
Most likely you lost a small amount of low end or possibly mid-range torque in exchange for a slight hp boost at high rpms.
Torque is what you use for acceleration, you don't really see the effect of hp until you get above the torque peak (or are cruising at a steady speed)
-
IIRC, I found that I can get a complete exhaust (catalytic converter and all) for somewhere between $300-600 USD on rockauto.com although I don't think that was including the manifolds.
-
also, can anyone give me detailed info on the sound system? i was on crutchfield and they dont have all the info. i know what mine has, but i wanted more detail than just what size speakers i have crammed in mine (the previous owner "fit" wal mart speakers in there, and its obvious they arent the stock size). hopefully someone who knows their pathy a little better can give me some more info like what exact size is supposed to be in there.
My '91 XE has 5-1/4" rounds in the doors and I believe 6x9's in the back (although I haven't checked to verify that)
According to Crutchfield, you can fit 6-1/2" rounds in the doors and 6x9's will fit in the back.
As for the specifications of the factory speakers, I suspect you have a google search ahead of you, if your local Nissan dealership can't tell you.
-
My Volvo had a similar problem, although it was a bit more obvious where the water was coming from. On that it was the windshield seal, and it was dripping onto the steering wheel.
Start by inspecting the windshield seal and also the weather seals on the door. Beyond that, good luck.
-
I don't know about the 4wd hubs, but on my 2wd it wasn't that hard (had to replace 3 on the front and 1 on the back). You have to separate the rotor from the hub in order to do it.
First take the caliper and bracket off. Then you have to remove the 6 14mm bolts holding the hub and rotor together. Use some penetrating oil such as PB Blaster where the rotor and hub meet and let that sit for a few minutes to an hour so it'll separate slightly easier. Then you just have to tap on the rotor with a rubber mallet. (If you don't have a mallet, place a block of wood against the rotor and hit the wood. The wood will protect the rotor from being damaged by the hammer.)
Once the rotor's separated, tap the broken stud out with a hammer and slip the new one into place. The best way to seat the new stud is to slip several washers over it and use a lug nut to pull it through until it's fully seated.
Once that's done all you have to do is reattach the rotor and put the caliper and bracket back on. (Unless of course, you're servicing the wheel bearings or replacing the rotors (which I did) at the same time.)
There you have it.
edit: I forgot about the dust shield behind the front rotors. Post corrected accordingly
-
If the A-arms are sitting parallel to the ground, how many notches should I adjust the bars to keep the adjustment close to stock?
-
I don't have access to the equipment to do a SAS project, and doubt I'll be doing any really heavy offroading any time soon, tbh. This fall I'll be heading back up to Missouri to attend Mizzou (University of Missouri in Columbia) and busting my butt trying to keep up with the kids who haven't been away from a school setting for 15 years.
Mild offroading for the occasional camping trip as well as a bit of extra traction and control for icy/snowy (mostly icy) roads is what I'm looking at.
Also, with the 720 (the pickup right before the D21) you can't convert a 2wd to a factory-style 4wd without a frame swap, as the suspension arms are mounted differently. That's why I'm asking for help in checking measurements.
-
Precise1, thanks for the body lift info.
Chriskaw440, if the measurements match, it really wouldn't be that hard to convert. If I'm right, all it will take is removing the transmission tailshaft, swapping the front spindles and oil pan, and installing the rest of the system from there. (Well, aside from the hole in the floor for the transfer shift lever, anyway)
I just need to make sure all the measurements are right.
-
Ok, I've been playing with the idea of converting Kumi (my '91 XE) to 4wd as part of getting her on the road, and need some info. I *do* know that the local pick 'n pull has the vehicles/parts available to make it cheaper (and much easier/quicker, locally) than hunting down a 4wd.
What I need is info related to what I'll need to accomplish it, and whether it can be done without a frame swap (which would mean buying a 4wd Pathy would be cheaper).
First off, I need to know if there are any differences in the manual transmissions (other than, say, removing the tailshaft to mount the transfer case), i.e. do they both use the same transmission, different variants of the same transmission (different cases), or completely different transmissions?
Second is the engine cradle. Are there any differences in the measurements for where the suspension arms mount? (If someone could post the measurements in a way that is easy to compare it would be very helpful) I know that the mount points for the arms are welded in as are the side portions of the cradle. I also need measurements for the bolt-in crossbars that form part of the cradle and serve as the mount points for the front diff.
Third comes suspension. Are the a-arms the same? What about springs/torsion bars, shocks, and sway bars? (I heard that the springs and torsion bars are, but would like verification)
Fourth would be the transmission crossbrace and mount. On this I need measurements locating where the crossbrace bolts to the frame, and verification that the transfer case takes the place of the crossbrace.
And finally, can someone verify the factory 2" body lift on the 4wd Pathys that I've read about?
I need as much checked and verified as possible before I even consider spending the money. If it's doable, and I can get it done, I may write a short tech article listing what's involved and what parts need to be changed to do it.
-
Summit lists the Doug Thorley headers as no longer available.
I think it's time to update the list again
-
Given what I've read in this thread, I think it would be reasonable to assume the difference is along the lines of suspension tuning, wheel options, and possibly brakes
-
'91 XE 241,000 miles when I got her
-
The local pick 'n pull has the speaker panel, they just don't have *any* red interiors (or grills, or front lights, or.....)
-
Thanks for the info on those two items, though I admit I was already aware of the timing belt
I'll try and get some pictures as soon as she's on the road. I just need to finish the brake rebuild, fix the reverse lights, and get tires. Well, and possibly re-index the torsion bars, if the front's sagging too much for adjusting them.
As for taking her off-road, it's a possibility in the future, but in about 4-5 years I intend to be in Japan as an english teacher. I might just take her with me, if I can.
Oh, and a couple of days after my initial post, she gently corrected me. Her name's Kumi, not Kimiko lol
-
So no matter how old the vehicle or how many owners it's had, Nissan will replace the seatbelt free?
Also, regarding the headliner issue....
I have yet to see another Pathy in my area with a red interior, junkyard or otherwise. Around here they all seem to have either blue or grey. This goes for the pickups as well. That's why I was asking about color options (so I know what to look at and what to ignore in the junkyard) and production numbers (so I know how likely I am to even find it)
-
Man you guys are hard on him....
If it is any consolation, many of us have done dumber things at one time or another. Good for you for sticking with it to get it resolved.
Anyone care to share a dumber story? I almost sold an old truck I had because I put the ditributor in 180° out of sync and it wouldn't start anymore.
'87 Firebird I sent to the junkyard after spending nearly a year trying to get it running after the engine blew. It took forever to find an engine I could afford. I had the engine in, everything hooked up and whatnot.....the gas in the tank had gone bad.
-
GM uses the same spacing on the 6-lug wheels they put on their trucks. I'm not sure about the backspacing, but I know they fit
-
Hi, can anyone tell me what the color options (exterior and interior)were for '91, and possibly how many were produced? My Pathy's dark red with a red interior and I'm trying to find a few interior parts (the driver's seat belt is badly frayed, for example, and maybe a headliner with the rear speaker panel up top (I'm not sure what years had that option, though) so I can get rid of the space-wasting pods on the sides. Can that be done if you have the interior spare tire carrier?)
-
Hi, I'm new to NPORA and Pathfinders in general. I recently acquired a 2wd '91 XE as a title for title trade for an old beat up bike (it was a 1980 Honda CB650 that needed a lot of work and the guy wanted a project bike). It has 241,000 miles on it and needs a bit of work but runs great. The paint's in great condition, but there are some dents and dings (of course). I think the most major thing it needs is some of the body work (front end collision, needs the radiator support, bumper, etc. It's fine as-is but I intend to fix it). Other than the front end there are only a couple of dents that need pulled out: front passenger door skin needs popped back out, and the lower d/s quarter also. Other than that and normal wear items it's mostly just freshening it up a bit.
Over the years I've had: '73 Honda CB500, '77 Ford Fairmont, '82 Pontiac Bonneville (nicknamed Bonnie), '87 Firebird (a project I never finished), '90 Thunderbird, '99 Mustang GT (made it a 12-13 second car for ~$1500 until an idiot decided to turn left from the right-hand lane. grr), '87 Volvo 245DL (current, nicknamed Sven), and the '80 CB650 I traded for the Pathy (who seems to want me to call her Kimiko). Strangely, all but the '73 bike (blue) and the Mustang (white) were/are red (Sven was originally brick red, but a previous owner painted him gold). It wasn't deliberate, that's just how things turned out.
I've always done all my own wrenching, and I miss each and every single vehicle I've ever owned.
Kimiko's my first asian vehicle and first truck/SUV, and my second manual trans vehicle (the bikes don't count on that one). She's dark red with red interior, interior mounted spare, and 6-spoke steel wheels. If anyone's interested I can see about uploading some pictures some time soon.
Anyway, enough rambling (bragging, boasting, ranting, babbling, whatever you choose to call it lol). It's nice to meet you all, and I hope to learn a lot about these strange creatures known as Pathfinders here.
Cheers,
Quentin
Not *exactly* new, but...
in New People Start Here!
Posted
I was here a few years ago, unfortunately life conspired against me, now I'm back! This time with a '93 SE automatic 4wd in need of help with rust...