-
Posts
58 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Posts posted by Tn95rbn
-
-
15ish sounds fair..might be hard to find someone willing to buy knowing they have repair of the bat
-
so good news bad news...column cover is in perfect shape...but not a tilt column...could probably cut the slot in it..but lewt me know before its gone
- 1
-
its faster to say what i havent done..uca bushings and centerlink.will be a 90% front end rebuild.but my next sunny weekend will fixthat.
-
-
All the screws are ofcourse on the inside but if you can look under and up behind the handle theres a hole where the plastic pin is.The pin sits on a small spring...alittle screwdriver or tool of choice should beable to pop the spring off its little mouint without causing any damage...it just sits on a little nub of plastic on the "backside" ofthe little hole...make sure itsnot locked..should be easy enough to do...goodluck
-
there's an 89 d21 se with a blue column cover that looked quite good at my local pull a part..cigarette lighter looked fine too...thats a match to a 92 pathfinder right? Ican check on it in the morning if you think its what ur wanting.
-
So 15 years later...I bought my 95 xe for 700 cash with 167k miles..couple dings and needing every bushing replaced but I think I stole it..
- 2
-
What's up Kruppanier814 .I'm down the road in Lebanon.The members on here are as helpful and as knowledgeable a group you could hope to find.Welcome to NPORA.
-
Appreciate the input.Think I'm going to hook up a relay and switch with a 15a inline fuse.The factory light wiring is ridiculously thin,not sure how it's lasted this long.maybe one day I'll go through and upgrade it all.
-
True enough.Are aftermarket CV's noticibly different than what I believe are the factory originals?
-
1 minute ago, PathyDude17 said:
It would suck to replace the boots only to have your CV fail anyway, and common consensus is to just replace the the entire axle, which by the way, may take some time to fail. I've been on torn boots for about 5 or 6 months, seeing dust, dirt, snow, and mud, and 4WD still works fine.
Cut the bumper insert and installedy jy fog light on the passenger side... (Dumb non ppe wearing me cut the crap outta my hand) Boys and girls..wear gloves!!.. Driver side tomorrow... Looks purdy if I do say so myself.PO had an alarm wired up with a switch mounted right under the little dash cubby hole to the left of steering wheel with red light mounted next to defrost switch on the dash...gonna hijack the wiring for my lights.
-
Cut the bumper insert and installedy jy fog light on the passenger side... (Dumb non ppe wearing me cut the crap outta my hand) Boys and girls..wear gloves!!.. Driver side tomorrow... Looks purdy if I do say so myself.PO had an alarm wired up with a switch mounted right under the little dash cubby hole to the left of steering wheel with red light mounted next to defrost switch on the dash...gonna hijack the wiring for my lights.Are trans coolers directional??Also...would replacing ripped boots after cleaning and re greasing my CV joints work??..I'd like to continue using them if possible...
-
Endlink bushings up front helped the steering even more.A 99 r50 had great OE fog lights mounted.The bracket were there as well but didn't seem like they'd fit around the Wd21 bumper insert so just took the light housings and fabbed up some brackets.Not sure if I want them wired independently of the other lights or splice them into the low beam wiring.. @ 2x 55w they put out a descent amount of light on there own.
-
Received my NPORA decal in the mail.SFcreations...Y'all rock..looks great!..
- 1
-
Went to the pull a part.Found OE fog lights. Pulled a trans cooler off an explorer(although not sure of the size/rating).However it's measured. Also an original tool kit.Ran out of daylight but I'll install the lights and cooler tomorrow.
- 3
-
In good shape...but...it looks like it belongs on the front of a dune buggy...full size but the treads an inch deep and diamond shaped
-
Endlink bushings.. Yaaaa..only 84 more to replace
- 1
-
I'm guessing I misread or was thinking of someone completely different then.Good to know though.Will definitely read it and thanks for the input.
-
Took out the front seats and cleaned everything properly..thinkin'. Maybe I'll do the same with the console tomorrow.. Gonna check on a r50 one first at the pull a part... C'mon cup holders.
- 1
-
I was thinking of working 2002 into my patch design..maybe roman(MMII)...maybe Mr. Jim...added as well...did I see he had passed away?...To anyone that knew him...anything particular that would "fit" regarding him?? Location or anything special...just kinda looking for inspiration.
-
Thanks man
-
Removed the center headliner to fix the sagging vinyl.trying to fix a slight leak in the passenger part of windshield exterior trim.
-
Question for an Admin. I suppose...when was NPORA started? Who started?..
-
Strut rod bushings installed on both sides. About to go check that they haven't loosened since install.No torque wrench..but tight as f@#k seems about right. Things hadn't moved since they spoke Japanese.
- 1
What did you do to your Pathfinder today?
in The Garage
Posted
Swapped out my 95 factory console for a 99 console.uca frame bolts haven't moved since they spoke japanese,but trying to get at the bushings. My camber is way off..centerlink patiently waiting.