masonl286 Posted June 26, 2020 Share Posted June 26, 2020 (edited) Hey guys, I know I am going to ruffle some feathers here on an offroad forum asking about lowering springs, but I am not sure where else to turn. There is very little information about it online, as it seems everyone and their uncle slaps a 2" lift on these babies and honestly, thats originally what I had planned on doing to mine. Unfortunately, as I was trying to get it saftied about a month ago (I wanted to get a car again), I was told I had an insta-fail due to underbody rust and since I am not a great mechanic and dont have a lot of money, I realized I wouldn't be able to sell my truck anymore, but I still have the urge for something low and fast. I've always wanted to do something different than what is normally seen with certain cars (ex had all parts picked out and priced to lift my old 02 Jetta VR6 until the timing chain needed to be changed for $2k+), so I decided I want to make this more of a performance truck, because lift kits + all accessories needed to make it an offroad beast would cost much more (hypothetically) than just lowering it. Plus, I'm not much of an offroader Anyways, so far through my research I have only found this thread: Which lead me to these https://www.4x4parts.com/i-18980579-pathfinder-lowering-coils-2wd.html But, alas they're R51 Coils. So now I am wondering is it even possible to lower an R50 without cutting the springs or buying a whole new shock setup to accommodate different springs? Thanks for any help, and if you just want to tell me I'm dumb for lowering a Pathy, trust me I know. Here she is btw https://imgur.com/gallery/LSHkuV9 Edited June 26, 2020 by masonl286 1 Link to comment Share on other sites More sharing options...
mvlzmarv Posted June 26, 2020 Share Posted June 26, 2020 Mine were lowered from old saggy springs before I opted for the OME/LR spring combo No cutting required. Ride quality not included. LolSent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
masonl286 Posted June 27, 2020 Author Share Posted June 27, 2020 1 hour ago, mvlzmarv said: Mine were lowered from old saggy springs before I opted for the OME/LR spring combo No cutting required. Ride quality not included. Lol Sent from my iPhone using Tapatalk Can you expand on what an OME/LR spring combo is? And how bad was the ride quality haha Link to comment Share on other sites More sharing options...
XPLORx4 Posted June 27, 2020 Share Posted June 27, 2020 OME/LR combo refers to Old Man Emu + Land Rover springs. However, that's of little help without information about whether those springs lifted, lowered, or kept the ride height. The mention of part numbers or vendor information would also be helpful. Link to comment Share on other sites More sharing options...
Guest Posted June 27, 2020 Share Posted June 27, 2020 Mine were lowered from old saggy springs before I opted for the OME/LR spring combo No cutting required. Ride quality not included. LolSent from my iPhone using TapatalkThis has nothing to do with what OP has asked...Sent from my Pathfinder Link to comment Share on other sites More sharing options...
Guest Posted June 27, 2020 Share Posted June 27, 2020 Can you expand on what an OME/LR spring combo is? And how bad was the ride quality hahaAll I can really think of without cutting oem springs is having very very worn springs. Check out nicoclub. They are more down this alleySent from my Pathfinder Link to comment Share on other sites More sharing options...
masonl286 Posted June 27, 2020 Author Share Posted June 27, 2020 10 minutes ago, R50JR said: All I can really think of without cutting oem springs is having very very worn springs. Check out nicoclub. They are more down this alley Sent from my Pathfinder Thanks, I'll have to make an account on there too haha Link to comment Share on other sites More sharing options...
PathyDude17 Posted June 27, 2020 Share Posted June 27, 2020 These are what you’re looking for: https://www.4x4parts.com/i-18981107-pathfinder-lowering-coils.html 2 1 Link to comment Share on other sites More sharing options...
mvlzmarv Posted June 27, 2020 Share Posted June 27, 2020 To further expand, I had a lowered r50 when it was on old worn and saggy suspension. I’ve since refreshed the suspension to the Combo mentioned earlier which lifted the truck. If you look into feedback with using ome front springs and Land Rover springs in the rear somewhere in the forums, you will find a big increase in both off road and on road performance. I’ve been playing with a Nissan 240sx for the last 16years with 3 chassis with full coilovers and adjustable arms.I can tell you the pathfinder’s Macpherson setup is similar to the 240sx while the rear Solid axle I similar to an AE86 corolla and mustangs 2014 and older.I don’t remember any aftermarket support to lower the pathfinder so you will have to be creative with your solution. Most lift kits discussed in this forum include increased spring rates to support added weight from steel bumpers and other overlanding gear. On its own the increased spring rates on-road performance aside from the lift raising the center of gravity.So theoretically you can look up “Bax03Se”Username and what he did to his rig with custom springs up front and Land Rover springs in the back and cut to your desired height.You will want a stock length or shorter shocks/struts. The rears May be easy but the front will be involved. You will have to consider the axle angle if you want to keep 4wd. And since they only make OE style front struts you will have to find ones for another car that is shorter and weld in the ears to mount to the stock knuckle and reuse Oe style top hats.I’m not sure how serious or dedicated you are to this idea. But if you are, I definitely would love to see the end result. Link to comment Share on other sites More sharing options...
mvlzmarv Posted June 27, 2020 Share Posted June 27, 2020 These are what you’re looking for: https://www.4x4parts.com/i-18981107-pathfinder-lowering-coils.htmlI wish I saw this post before I hit send on my long winded reply. Lol Link to comment Share on other sites More sharing options...
Guest Posted June 27, 2020 Share Posted June 27, 2020 To further expand, I had a lowered r50 when it was on old worn and saggy suspension. I’ve since refreshed the suspension to the Combo mentioned earlier which lifted the truck. If you look into feedback with using ome front springs and Land Rover springs in the rear somewhere in the forums, you will find a big increase in both off road and on road performance. I’ve been playing with a Nissan 240sx for the last 16years with 3 chassis with full coilovers and adjustable arms. I can tell you the pathfinder’s Macpherson setup is similar to the 240sx while the rear Solid axle I similar to an AE86 corolla and mustangs 2014 and older. I don’t remember any aftermarket support to lower the pathfinder so you will have to be creative with your solution. Most lift kits discussed in this forum include increased spring rates to support added weight from steel bumpers and other overlanding gear. On its own the increased spring rates on-road performance aside from the lift raising the center of gravity. So theoretically you can look up “Bax03Se”Username and what he did to his rig with custom springs up front and Land Rover springs in the back and cut to your desired height. You will want a stock length or shorter shocks/struts. The rears May be easy but the front will be involved. You will have to consider the axle angle if you want to keep 4wd. And since they only make OE style front struts you will have to find ones for another car that is shorter and weld in the ears to mount to the stock knuckle and reuse Oe style top hats. I’m not sure how serious or dedicated you are to this idea. But if you are, I definitely would love to see the end result.What? I mean no offense, but what you have stated is not only confusing but completely irrelevant to OP’s initial question. Sent from my Pathfinder Link to comment Share on other sites More sharing options...
mvlzmarv Posted June 27, 2020 Share Posted June 27, 2020 What? I mean no offense, but what you have stated is not only is confusing but completely irrelevant to OP’s initial question. Sent from my Pathfinder I tried and said way too much. Sorry you got lost in my sea of words 1 Link to comment Share on other sites More sharing options...
masonl286 Posted June 27, 2020 Author Share Posted June 27, 2020 (edited) 8 hours ago, PathyDude17 said: These are what you’re looking for: https://www.4x4parts.com/i-18981107-pathfinder-lowering-coils.html How did you find these?!?!? I cant count how many times and different ways I've search up Pathfinder Lowering Springs/Coils and that never came up... You're amazing. Now I just got to see if it's worth forking over $400USD for EDIT - Looking at that site, it says its recommended to replace the rear shocks as well, why is that? Can I do this with just the coil springs or do I have to replace the rear shocks? And if I do have too, what's the cheapest option? So far I'm looking at around $600+ Canadian just to get the Coils delivered to me haha Edited June 27, 2020 by masonl286 Link to comment Share on other sites More sharing options...
Guest Posted June 27, 2020 Share Posted June 27, 2020 How did you find these?!?!? I cant count how many times and different ways I've search up Pathfinder Lowering Springs/Coils and that never came up... You're amazing. Now I just got to see if it's worth forking over $400USD for EDIT - Looking at that site, it says its recommended to replace the rear shocks as well, why is that? Can I do this with just the coil springs or do I have to replace the rear shocks? And if I do have too, what's the cheapest option? So far I'm looking at around $600+ Canadian just to get the Coils delivered to me hahaYou want to replace the shocks because they will bottom out since the resting height of the vehicle will already be much lower with those springs. You’d want a shorter shock with smaller compressed length. Sent from my Pathfinder Link to comment Share on other sites More sharing options...
PathyDude17 Posted June 27, 2020 Share Posted June 27, 2020 1 hour ago, masonl286 said: How did you find these?!?!? I cant count how many times and different ways I've search up Pathfinder Lowering Springs/Coils and that never came up... You're amazing. Now I just got to see if it's worth forking over $400USD for EDIT - Looking at that site, it says its recommended to replace the rear shocks as well, why is that? Can I do this with just the coil springs or do I have to replace the rear shocks? And if I do have too, what's the cheapest option? So far I'm looking at around $600+ Canadian just to get the Coils delivered to me haha I searched “pathfinder lowering coils 4x4parts” and it was the 2nd result 1 Link to comment Share on other sites More sharing options...
masonl286 Posted June 27, 2020 Author Share Posted June 27, 2020 7 hours ago, PathyDude17 said: I searched “pathfinder lowering coils 4x4parts” and it was the 2nd result you're blowing my mind 8 hours ago, R50JR said: You want to replace the shocks because they will bottom out since the resting height of the vehicle will already be much lower with those springs. You’d want a shorter shock with smaller compressed length. Sent from my Pathfinder ok that makes sense, thank you Link to comment Share on other sites More sharing options...
RainGoat Posted July 3, 2020 Share Posted July 3, 2020 4x4Parts is also a notorious Pathfinder aftermarket supplier. Definitely check the shipping - it’s unreasonably expensive in the US, I shudder to think what it will be to Canada. 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now